Monday, November 16, 2026

 



Dear friends,

It has been a long time since I last published a post on my blog. Today, I would like to share my latest experimental project involving the CODAN Envoy X1 HF transceiver.

As you may know, the CODAN Envoy is a rather restrictive device when it comes to additional features and external equipment. Many functions require separate licenses or optional features that must be ordered at the time of purchase.

For example, controlling an external RF power amplifier normally requires a dedicated HPA (High Power Amplifier) interface, which I don't have.

Therefore, I decided to design and build a simple circuit board that allows the transceiver to key an external RF power amplifier or control an external receive antenna switch.

The main goal of this project was to achieve this functionality using a simple, inexpensive, and practical solution without relying on additional CODAN hardware.


For my first prototype, I designed a very simple circuit using just a few basic electronic components: a resistor, an optocoupler, a relay, a diode, and a capacitor.

The circuit is easy to assemble and requires only a small number of inexpensive, commonly available components. 

List of components:

  • Optocoupler: TOSHIBA TLP627

  • Resistor: 330 Ω

  • Relay: 12 V DC

  • Diode: Any suitable diode for a 12 V DC relay coil (e.g., 1N4007)

  • Capacitor: 0.1 µF or 0.01 µF ceramic capacitor


I decided to use the TOSHIBA TLP627 optocoupler because it supports a collector-emitter voltage of up to 300 V DC and a maximum collector current of 150 mA, making it suitable for controlling an external relay.

In my case, I selected a 12 V DC relay with a coil current of just 33 mA. Since the TLP627 can handle this current, there is no need for an additional transistor, such as a 2N2222, or any other relay driver circuit.

After examining the CODAN Envoy X1's internal circuitry, I found a PTT-related control point on the band-pass filter board, where a 3.3 V signal appears whenever the transceiver switches to transmit mode (PTT activated).

I decided to use this 3.3 V signal to drive the TLP627 optocoupler through a 320 Ω resistor. This allows me to control an external 12 V relay while maintaining electrical isolation between the transceiver's internal control circuit and the external relay circuit.


Here is The circuit: 














I disconnected the cable from the P300 connector on the Transceiver Control Board (P/N 08-07158-001) and removed the wires from pin 15 (white) and pin 11 (black). These two wires provide power to the cooling fan and are routed to the rear panel of the transceiver alongside the CIB cable connector:




Next, I installed my custom-built circuit board in an available space inside the RF unit (there is plenty of unused space inside the unit) and connected the wires according to the schematic diagram 
shown above:





Next, I connected the black and white wires removed from the P300 connector to the relay's normally open (NO) contacts, which close whenever the transceiver switches to transmit mode (PTT activated).




This is the solution I came up with. I would be happy to hear your thoughts, suggestions, or experiences with similar modifications.

Best wishes to everyone!

73 de 4L2IK












Saturday, October 14, 2023

CODAN ENVOY CIB Cable Wiring Diagram

 

   Hello to everyone, Few days ago I bought CODAN Envoy X1 HF SSB Transceiver with Desk Console. The Connection cable (CIB Cable) between RF Unit and Desk Console has been lost. I Asked many people if someone can measure and check the cable connections with multimeter but no-one helped me. 
I ordered on eBay 8 Pin Male Connector which needed little bit adjust pin 1 and pin 7, also I bought 10 Pin Female Connector for RF unit, which fit well.


Here are wiring diagram of Handset and Desk Console to Envoy X1 / X2 RF Unit. All data are Ethernet 




Thank you for view.

73

Tuesday, October 18, 2022

CODAN 3012 HF DATA MODEM


 CODAN 3012 HF DATA MODEM


  Hello folks, few days ago I bought a brand new CODAN 3012 HF DATA Modem. This is a my first experience with 3012 modem. I have 9001 and 9002 modems, but they are very old. 

 I tried old DOS software by CODAN (for DATA transmit) but it didn't work. Also tried CLOVER MAIL, Airmail, Alpha, RMS Express but still nothing. I would like to find any software for this 3012 modem, guys if someone has this software, please share it. 

Best Regards








Tuesday, January 18, 2022

Using the NGT series without CIB cable

 Hello dear friends. I had one NGT radio without CIB cable. I found very easy way to using the radio without CIB cable. I just removed 7 and 10 pin connectors and make the cables directly soldered. Also I disconnected FAN connector and this cable used for the speaker. it works very well!












Friday, August 13, 2021

Installation of the CODAN Envoy X1

 Here is a photo collage about instalation of the CODAN Envoy X1 into my Toyota Land Cruiser HZJ 105

 

 1) Installed Grounding Cable under the passenger seat:

 
2) Drilled holes and installed bracket of the RF Unit

 

3) Installed RF Unit:

4) Ground is Connected:

5) Started wiring:

 
6) extra cables rolled and hidden under bar:




 
7) Speaker has installed on the Ashtray
 





 


Thanks!

Monday, July 12, 2021

CODAN 3040 Antenna Tuner

 I would like to Introduce internal photos of the CODAN 3040 antenna tuner










Wednesday, December 23, 2020

How to program CODAN X2 HF SSB Transceiver

 

Tutorial: how to program old CODAN X2 SSB Transceiver. It's very easy!



Thank you for watching